Statement of Coal Resources and Reserves
in Accordance with SEC and the JORC Code as of December 31, 2023
Northern and Central Appalachian Coal Basins –
Virginia, West Virginia and Pennsylvania, USA
M
ARSHALL
M
ILLER
&
A
SSOCIATES
I
NC
.
2
Criteria
JORC Code explanation
Commentary
Logging
>
Whether core and chip samples have been geologically and geotechnically logged to a level
of detail to support appropriate Mineral Resource estimation, mining studies and
metallurgical studies.
>
Whether logging is qualitative or quantitative in nature. Core (or costean, channel, etc.)
photography.
>
The total length and percentage of the relevant intersections logged.
>
A wide variety of core-logging techniques exist for the properties.
For many of the core holes, the
primary data source is a generalized lithology description by the driller, in some cases
supplemented by a more detailed core log completed by a geologist.
>
The logging of core thickness and depth is quantitative.
With the exception of the coal seams,
logging of rock strata type is more subjective and best considered as qualitative.
Sub-sampling
techniques and sample
preparation
>
If core, whether cut or sawn and whether quarter, half or all core taken.
>
If non-core, whether riffled, tube sampled, rotary split, etc. and whether sampled wet or dry.
>
For all sample types, the nature, quality and appropriateness of the sample preparation
technique.
>
Quality control procedures adopted for all sub-sampling stages to maximise representivity of
samples.
>
Measures taken to ensure that the sampling is representative of the in situ material
collected, including for instance results for field duplicate/second-half sampling.
>
Whether sample sizes are appropriate to the grain size of the material being sampled.
>
Typical US practice in the Appalachian Basin is that core samples for deep mineable core samples
are not sawn or subsampled (since seams are not of great thickness and the entire seam is mined
and co-mingled). The entire coal interval drilled is generally analyzed.
>
Oftentimes, core for surface-mineable coal seams are bench sampled separately by the various
coal and rock layers (plies).
>
MM&A has exercised diligence to use only those analyses that are representative of the coal
quality parameters for the appropriate mining type for each sample.
Quality of assay data
and laboratory tests
>
The nature, quality and appropriateness of the assaying and laboratory procedures used and
whether the technique is considered partial or total.
>
For geophysical tools, spectrometers, handheld XRF instruments, etc., the parameters used
in determining the analysis including instrument make and model, reading times,
calibrations factors applied and their derivation, etc.
>
Nature of quality control procedures adopted (e.g. standards, blanks, duplicates, external
laboratory checks) and whether acceptable levels of accuracy (i.e. lack of bias) and precision
have been established.
>
Sample analysis was typically carried out by accredited US laboratories.
>
Standard procedure upon receipt of core samples by the testing laboratory is to log the depth and
thickness of the sample, then perform testing as specified by a representative of the operating
company.
Each sample is then analyzed in accordance with procedures defined under
ASTM
International (
ASTM
)
standards including, but not limited to; washability (ASTM D4371); ash
(ASTM D3174); sulfur (ASTM D4239); Btu/lb. (ASTM D5865); volatile matter (ASTM D3175); Free
Swell Index (
FSI
) (ASTM D720).
>
Geophysical tools are calibrated by the logging company and where possible, validated using a
calibration hole.
Verification of
sampling and assaying
>
The verification of significant intersections by either independent or alternative company
personnel.
>
The use of twinned holes.
>
Documentation of primary data, data entry procedures, data verification, data storage
(physical and electronic) protocols.
>
Discuss any adjustment to assay data.
>
All coal intersection data used to generate the geologic model has been cross referenced with the
lithological and geophysical logs by MM&A.
>
Laboratory quality was adjusted from dry basis to reflect the anticipated marketable product
moisture.
>
Coal quality results were verified by spot-check with laboratory analysis sheets by MM&A before
inclusion into the geologic model and use in the resource estimate.
Location of data points
>
Accuracy and quality of surveys used to locate drill holes (collar and down-hole surveys),
trenches, mine workings and other locations used in Mineral Resource estimation.
>
Specification of the grid system used.
>
Quality and adequacy of topographic control.
>
Due to the long history of exploration by various parties on the Properties, a wide variety of survey
techniques exist for documentation of data point locations.
Many of the older exploration drill
holes appear to have been located by ground survey; more recently completed drill holes are
often located by high-resolution Global Positioning System (
GPS
) units.
>
Grid systems used are typically the State Plane Coordinate System pertinent to each property.
>
Topography is based on either the USGS topographic 7.5-minute quadrangle maps or on recent
aerial photogrammetry as necessary (subject to availability).